Genie Clip Single, also known as the GenieClip RST, is a resilient sound isolation clip used to reduce sound transfer through wall and ceiling systems. It is designed to decouple plasterboard from the supporting structure, helping reduce both airborne noise and impact vibration when used with suitable furring channel and acoustic plasterboard.
The Genie Clip is made from a unibody moulded rubber and galvanised steel construction. It is commonly used in high-performance soundproofing systems for party walls, ceilings, studios, music rooms, cinema rooms, flats, apartments and commercial spaces.
Genie Clips are used to create a resilient separation between the plasterboard layer and the wall or ceiling structure behind it. This helps reduce direct vibration transfer, which can significantly improve the acoustic performance of the full build-up.
They are commonly used as part of:
A Genie Clip is fixed to the existing wall or ceiling structure. A compatible furring channel is then snapped into the clip, and plasterboard or acoustic plasterboard is fixed to the channel rather than directly to the wall or ceiling frame.
This creates a decoupled plasterboard layer. The rubber element within the clip helps absorb vibration and reduce the transfer of sound energy through the structure.
This is different from fixing plasterboard directly to studs, joists or masonry, where vibration can pass more easily through the connected materials.
Genie Clips can help reduce both airborne noise and impact noise when used as part of a complete acoustic system.
Airborne noise includes voices, TV noise, music, traffic noise and general room-to-room sound transfer.
Impact noise includes footsteps, dropped items, furniture movement and vibration through floor and ceiling structures.
The final result will depend on the full build-up, including existing structure, insulation, clip spacing, furring channel, plasterboard layers, sealing detail and flanking noise paths.
Genie Clips are suitable for a range of wall and ceiling applications, including:
Genie Clips are a high-performance alternative to basic resilient bar systems. The clip and channel system is designed to reduce the risk of acoustic short-circuiting when installed correctly, while providing a more controlled decoupling detail for walls and ceilings.
They are quick to install, require only one suitable fixing per clip, and allow compatible furring channel to be snapped into position before the plasterboard layers are fitted.
Both Genie Clips and resilient bars are used to decouple plasterboard from a wall or ceiling structure. The difference is that Genie Clips use an individual rubber and steel isolation clip with a separate furring channel, whereas resilient bar is a continuous metal profile.
Genie Clips are generally considered a more robust decoupling option because the plasterboard is fixed to the furring channel rather than directly through a resilient bar into the structure behind. This helps reduce the risk of short-circuiting when installed correctly.
Genie Clips are not a complete soundproofing system on their own. They should be used with compatible furring channel, acoustic plasterboard, acoustic mineral wool, acoustic sealant and correct perimeter detailing.
The number of clips required depends on the wall or ceiling size, furring channel spacing, board weight and system specification. Always check the correct spacing and loading requirements before installation.
If you are unsure how many Genie Clips you need, or whether this is the right decoupling system for your project, please contact our team before ordering. We can help advise on the correct acoustic wall or ceiling build-up.
Genie Clip Single is a resilient acoustic isolation clip used with compatible furring channel to support plasterboard in wall and ceiling soundproofing systems. It is designed to reduce direct vibration transfer between the structure and the plasterboard lining.
| Product Name | Genie Clip Single |
| Product Type | Resilient sound isolation clip / acoustic decoupling clip |
| Common Product Reference | GenieClip RST |
| Material | Unibody moulded rubber and galvanised steel mount |
| Application | Wall and ceiling soundproofing systems |
| Suitable For | Walls, ceilings, floor/ceiling assemblies, studios, cinema rooms, music rooms and acoustic plasterboard systems |
| Pack Size | 1 clip |
| Approx. Dimensions | Approx. 40–41mm wide x 63–64mm long/high x 24–25mm deep, depending on manufacturer orientation |
| Approx. Clip Weight | Approx. 40–47g per clip, depending on supplier data |
| Maximum Acoustic Design Load | Approx. 16kg / 36lb per clip according to manufacturer installation data |
| Compatible Channel | Compatible plasterboard furring channel / hat channel with hemmed edges |
| Channel Height | Typically 22mm furring channel, depending on system specification |
| Maximum Clip Spacing | Manufacturer guidance lists maximum 48 inches / 1219mm on centre along the furring channel |
| Maximum Furring Channel Spacing | Manufacturer guidance lists maximum 24 inches / 609mm on centre |
| Main Noise Types | Airborne noise and impact vibration, depending on full system build-up |
| Fixing Method | Fixed to timber, steel, masonry or concrete substrates using suitable approved fixings |
| Minimum Fixing Strength | Manufacturer guidance requires fixings with minimum 120lb pull-out or shear strength in the substrate |
| Important Fixing Note | Do not over-tighten fixings, as this can reduce acoustic performance |
| Fire Rating | System-dependent — confirm the full tested wall or ceiling build-up before compliance-led use |
| Standalone Product? | No — should be used as part of a complete acoustic wall or ceiling system |
Genie Clips can be used in a range of acoustic applications, including:
Genie Clips are used to decouple plasterboard from the supporting wall or ceiling structure. By separating the board layer from the structure, the system helps reduce vibration transfer and improves the sound insulation of the overall build-up.
The clip should be used with compatible furring channel and suitable board layers. Acoustic mineral wool, acoustic sealant and correct perimeter isolation are normally used alongside the clip and channel system.
Genie Clips are acoustic decoupling components, not complete soundproofing systems on their own. The final result depends on the full wall or ceiling build-up.
Clip spacing, furring channel spacing, plasterboard weight, insulation, perimeter sealing, substrate type, fixing method, workmanship and flanking noise paths can all affect performance.
Published system figures should be treated as system-dependent. For Building Regulations, fire-rated or compliance-led projects, use the correct tested specification and seek project-specific acoustic advice where required.
Store Genie Clips clean, dry and protected before installation. Check that the supporting structure is suitable before fitting.
Do not install onto weak, loose, rotten or unstable substrates. Do not over-tighten the fixing through the clip, as excessive compression can reduce the acoustic isolation performance of the rubber element.
Genie Clips are installed to the supporting wall or ceiling structure and used with compatible furring channel to create a decoupled plasterboard lining. The system helps reduce sound transfer by separating the plasterboard from the structure behind it.
For best results, Genie Clips should be installed as part of a complete acoustic wall or ceiling system, using the correct clip spacing, furring channel, board layers, insulation and acoustic sealing.
Check the wall or ceiling structure before installation. The structure should be stable, dry and capable of supporting the full acoustic system, including clips, furring channel, plasterboard layers and any additional acoustic materials.
Plan the layout before fixing the clips. The number of clips required depends on the room size, board weight, channel spacing and acoustic specification.
Check that the fixings are suitable for the substrate. Manufacturer guidance states that fixings should provide a minimum pull-out or shear strength of 120lb in the supporting substrate.
Make sure the installation area is ready. The substrate should be:
Repair loose boards, damaged studs, unstable masonry or weak ceiling areas before installing the clips.
Where the system requires cavity treatment, install acoustic mineral wool before the plasterboard layers are fitted.
For walls, insulation is commonly fitted between studs or within the wall lining cavity. For ceilings, insulation is commonly installed between joists.
The insulation should fit neatly without being over-compressed and should not interfere with the clip and channel system.
Mark the furring channel lines on the wall or ceiling.
Manufacturer guidance commonly uses furring channel rows at a maximum of 24 inches / 609mm centres, with Genie Clips spaced at a maximum of 48 inches / 1219mm centres along the channel.
For walls, the bottom row of furring channel should usually be positioned around 3–6 inches / 76–152mm from the floor, with the top row close to the ceiling.
For ceilings, the first and last rows should usually be positioned close to the wall edges, again around 3–6 inches / 76–152mm from the perimeter.
Always follow the project-specific layout or manufacturer guidance where provided.
Fix each Genie Clip to the structure using a suitable approved fixing for the substrate.
Common substrates include:
Tighten the fixing until it comes into contact with the top washer of the Genie Clip. Do not over-tighten. Over-tightening can compress the resilient element and reduce acoustic performance.
Snap the compatible furring channel into the Genie Clips.
Make sure the channel is fully seated and runs straight across the wall or ceiling. Furring channel should be installed perpendicular to studs or joists, depending on the system.
Where channels need to be joined, overlap the channel ends in the middle of the span between clips. Manufacturer guidance commonly refers to a 6 inch / 150mm overlap, secured with suitable wire or framing screws.
Do not cantilever the furring channel excessively beyond the final clip.
Before installing plasterboard, check the full clip and channel layout.
Check that:
Correct any issues before fitting plasterboard.
Install the plasterboard onto the furring channel using suitable drywall screws.
Only fix the plasterboard to the furring channel. Do not screw through into the studs, joists, masonry or structure behind, as this can create an acoustic bridge.
Leave a small perimeter gap around the plasterboard. Manufacturer guidance commonly refers to a minimum gap of around 1/4 inch / 6mm around the board perimeter, supported temporarily with shims until the board is fixed.
If the system requires a second layer of plasterboard or acoustic plasterboard, install it after the first layer.
For best acoustic performance, stagger board seams between layers. Avoid lining up joints where possible.
Use the correct screw length so the screws fix into the furring channel without passing through into the structure behind.
Once the plasterboard layers are installed, remove any temporary shims and seal the full perimeter gap with non-hardening acoustic sealant.
Seal around:
Good sealing is important because sound can pass through small air gaps.
After the acoustic sealant has cured, tape and finish the plasterboard joints as required.
The final finish may include jointing compound, skim plaster, paint or another suitable decorative finish.
Do not fix heavy point loads such as cabinets, shelving or heavy equipment directly to the Genie Clip and plasterboard system unless the wall or ceiling has been specifically designed to support them.
For wall installations, Genie Clips are typically fixed to timber studs, metal studs or masonry walls. Furring channel is then installed horizontally, and plasterboard is fixed to the channel.
Avoid any direct plasterboard fixings into the structure behind. Any rigid bridge can reduce acoustic performance.
For ceiling installations, Genie Clips are typically fixed to timber joists or a suitable ceiling substrate. Furring channel is installed perpendicular to the joists, and plasterboard is fixed to the channel.
Ceiling systems must be designed to carry the full board weight. Check clip loading, fixing strength and board specification before installation.
Genie Clips can significantly improve the acoustic performance of a wall or ceiling system, but the final result depends on the complete build-up.
Existing structure, clip spacing, furring channel, plasterboard mass, insulation, fixing method, perimeter sealing and flanking paths can all affect the result.
If you are unsure how to use Genie Clips in your project, please contact our team before installation. We can help advise on the most suitable wall or ceiling soundproofing system based on your structure, noise issue and available build-up depth.
Before you continue, there are some essential items which we recommend you may need.
Sign up today and we’ll send your discount code straight to your inbox.
