Norsound NOR200 Finger Protection Full Set – 1950mm is a surface-mounted door-safety system designed to help prevent fingers from becoming trapped within the hazardous gaps around a hinged timber door.
As a door opens, a wide gap develops between the hinged edge of the door leaf and the frame. A smaller trapping point is also present around the hinge knuckles on the opposite face. The NOR200 Full Set provides protective components for both sides of the hinged edge.
The stocked range is supplied in a fixed 1950mm length with a choice of Silver Grey or White.
The full set provides:
This provides more comprehensive protection than a single-side product where both faces of the door are accessible.
The protectors bridge the changing hinge gaps as the door opens and closes, helping restrict access to areas where fingers could otherwise become trapped or crushed.
NOR200 is designed for surface mounting to suitable timber doorsets. It can therefore be used as a retrofit solution without routing a dedicated channel into the door leaf or frame.
The flexible PVC components are secured to suitable surfaces on the door and frame using the fixing method required by the current product instructions.
Published fixing options include:
The receiving surfaces must be clean, dry, secure and suitable for the selected fixing method.
Current technical information states that the NOR200 system can accommodate door openings of up to 180 degrees.
Actual suitability depends on the complete door geometry, including:
The installed protectors must not become excessively stretched, detach from the substrate or prevent the door from reaching its intended opening position.
The NOR200 Full Set is manufactured from flexible PVC. The material is designed to move with the door while maintaining a protective barrier over the hinge-side gaps.
Current technical data states that the product has been tested through 250,000 operating cycles.
Cycle testing demonstrates repeated operation under controlled test conditions. Regular inspection is still required, particularly on frequently used doors.
Current technical information references:
The product should still be selected according to the actual doorset, opening angle, frequency of use and site-specific risk assessment.
NOR200 may be suitable for internal timber doors in environments where hinge-side finger trapping has been identified as a risk.
Typical applications include:
Final selection should follow the building’s door-safety assessment and maintenance procedures.
The stocked finishes are:
Select the finish that best coordinates with the door leaf, frame and surrounding ironmongery.
Both variations are supplied in a fixed 1950mm length.
Before ordering, check that this length is suitable for the intended door and that the protector will remain clear of:
Do not trim the components unless trimming is permitted by the current manufacturer fitting instructions.
NOR200 is a finger-protection accessory rather than an intumescent or smoke seal.
Before installing it on a fire-resisting door, confirm that:
The NOR200 Full Set does not independently provide a fire-resistance or smoke-control classification.
Before ordering, confirm:
| Product Name | Norsound NOR200 Finger Protection Full Set – 1950mm |
| Product Reference | NOR200/FS |
| Product Type | Surface-mounted door finger-protection full set |
| Coverage | Opening-side hinge gap and opposite hinge-knuckle gap |
| Application | Hinge side of suitable timber doorsets |
| Material | PVC |
| Length | 1950mm |
| Installation Type | Surface mounted |
| Published Fixing | Self-adhesive or pinned |
| Published Maximum Door Opening | Up to 180 degrees, subject to the actual doorset geometry |
| Cycle Testing | 250,000 operating cycles |
| Certification | SKG certified to EN 16654 and NEN 8654 |
| Stocked Colours | Silver Grey and White |
| Unit of Sale | One complete full set |
| Fire Seal? | No |
| Standalone Fire Rating? | No — use on a fire-resisting door must be permitted by the complete doorset evidence |
| Colour | Length | Set Type | Product Code |
|---|---|---|---|
| Silver Grey | 1950mm | Full set | NOR200/FS/GRY |
| White | 1950mm | Full set | NOR200/FS/WHT |
| Colour Options | Length Options | Set Options | Total Variations |
|---|---|---|---|
| Silver Grey and White | 1950mm | Full set | 2 |
The exact component design and supplied fixing accessories should be checked against the current product pack and fitting instructions.
Before specifying NOR200, check:
Inspect the fitted protectors regularly for:
Replace damaged components rather than relying on temporary repairs.
The NOR200 Full Set provides two protective components: one for the large opening-side hinge gap and one for the smaller gap around the hinge knuckles on the opposite side.
Both components must be positioned so that they move freely with the door without becoming excessively stretched or preventing correct door operation.
Before installation, confirm that:
Correct any door-alignment, hinge or closing fault before fitting the finger protection.
Identify:
Do not install both components on the same side of the hinged edge.
Offer both 1950mm components to the door and frame without removing any release liner.
Confirm that they:
Only trim the components where this is permitted by the current fitting instructions.
Clean the corresponding areas of the door leaf and frame.
The surfaces must be:
Allow cleaned surfaces to dry completely.
Position the larger protector across the wide gap exposed as the door opens.
Check its alignment throughout the normal door-opening range.
The protector should:
Where using the self-adhesive fixing, remove a short section of the release liner and align the first fixing edge.
Remove the liner progressively while pressing the fixing surface firmly into position. Repeat for the opposing fixing edge.
Do not stretch the flexible centre section during application.
Where pinned fixing is required, install the pins only in the positions identified by the current fitting guide.
Move to the opposite face of the hinged edge and position the smaller protector across the hinge-knuckle gap.
Confirm that it:
Apply the self-adhesive fixing progressively without stretching or twisting the material.
Where pinned fixing is specified, use the current manufacturer fitting guide to determine the correct fixing positions.
Do not place fixings where they could damage hinges, seals or concealed doorset components.
Open and close the door slowly through its complete normal operating range.
Confirm that:
Stop and correct the installation if either protector interferes with the door or begins to detach.
Check that:
Inspect the NOR200 Full Set regularly, particularly on frequently used doors.
Replace a component where it becomes:
The NOR200 Full Set helps reduce access to hinge-side trapping points, but continued protection depends on correct installation, suitable door geometry and routine maintenance.
It should form part of the wider risk assessment and maintenance programme for the complete doorset.
Before you continue, there are some essential items which we recommend you may need.
Sign up today and we’ll send your discount code straight to your inbox.
